Phone Hours
Mon-Fri
9AM - 5 PM
Central Time
Local: 325-227-6903
Toll Free: 866-807-4337
Email: sales@electricrider.com Service Dept: 325-227-6903 Go green with a company who will back
you up! Buy with confidence, we'll be here when you need us!
ElectricRider
1301 Pulliam Street
San Angelo, TX 76903
In our 11th year of service to the electric bike and LEV community
Contents of a Phoenix II 3640 Power System Only
Kit
Complete systems from ElectricRider include
everything you need to convert your pedal bike at home or at a bike shop, and we
do a lot of the work for you. The wheel is laced to the motor and the batteries
are pre-wired. Although Phoenix II systems are priced for the DIY market, we
don't make you work very hard for it. Considering a Phoenix II system a DIY
project would be similar to considering a new coffee table you must assemble a
DIY project. There's a little assembly required, but nothing difficult. Every component we ship is tested just prior to shipment. Our goal is
zero defects in our customers' hands.
Power System Only kits from ElectricRider
include the main components necessary to convert your bike to electric except
batteries, charger, and a mounting system. The wheel is laced to the motor. Every
component we ship is bench tested just prior to shipment. The Power System
Only kit was created for those who prefer to experiment with other battery
technology, or already have a good battery source. If you do not have a
battery and charger, and do not have plans to purchase them elsewhere, order the complete kit rather than the Power System Only
kit.
Here are pictures of individual PARTS
for your perusal. You will also find hub system parts under parts categories.
Motor
We offer two types of motors, the Cruiser is wound for speed
and the Brute is wound for torque. Both motors are available in
front or rear, and can be laced to a 20in, 24in, 26in, and 700C rim. All
Phoenix II motors are disc brake compatible.
Spokes
We use 12 gauge spokes for all Phoenix II wheels. Normal
bike spokes are 14 gauge. Heavier spokes mean less spoke maintenance and a
stronger wheel. Each time you decrease one size in gauge, the thickness
doubles. For example, a 12g spoke is twice as thick as a 13g spoke.
Rim
For Phoenix II we offer 20", 24", 26",
and 700C rims. All of these rims are double-walled.
Lacing
We lace the motor to the rim on our bench. We tighten the
spokes to the correct tension, and make sure the wheel is true before
shipping.
Controller
The 3640 power system only kit comes with a 36 volt 40amp
controller (1440 watts). All Phoenix II controllers include plugs that
will only fit into their mating plug, so there is no chance of plugging
something in backward. Please note that even though only 3 pins may be
used of a 4 pin connector, it is still a 4-pin connector and should only
plug into its 4-pin mate. Plugs are identified by the total number of
pins/holes available, not the number of pins/holes being used.
7-Speed Freewheel (8-speed avail)
Anything from a single rear gear to an 8-speed freewheel is
compatible with Phoenix II motors. A 7-speed freewheel is shipped with all
rear wheel drive kits by default, however, you may request an 8-speed
instead for no additional charge.
Throttle
Three types of throttles are available for your Phoenix II
system: Thumb Throttle, Half-Twist Throttle, and Full-Twist Throttle.
If you do not specify, you will receive a thumb throttle. You can see
pictures of all the throttles we offer on our parts
page. If you have twist shifters, choose a thumb throttle because the
shifters take the space on the handlebar used by other models. All
throttles are non-lighted for Phoenix II since the APM-Display monitors
your battery capacity much more accurately.
APM-Display (Active Power Management Display)
The APM-Display is included with all Phoenix II complete
kits and power system only kits. The APM-Display is a toolbox for the
Phoenix II owner, offering specific information about power consumption,
efficiency, RPM, Voltage, etc. Please see the APM-Display Owner's Manual
for details.
Spoke Wrench
We include a spoke wrench with all of our kits. The spoke
wrench is a metal ring about 1" diameter that has notches cut out.
Keep an eye out for this in your package as it is not obvious to most. The
spoke wrench can usually be found packaged with the throttle unit.
Things you may want to add:
WireSet includes fuse, jumpers, charger port, and connection to controller.
If your battery already comes with these parts, a wireset is not needed, but if
it doesn't, the cost of the set is quite a bit less than the individual
components.
Lights, Mirrors, Double Kickstand. Lights and mirrors improve the safety of your
ride. Since adding a Phoenix II system to your frame makes your frame much
heavier, a double kickstand may be desired in order to keep your bike from
falling. Regular bicycle kickstands tend to bend, break, or simply won't hold
the extra weight of your Phoenix II. Double kickstands can be cut or modified to
offer the desired fit to your frame. For all other accessories, please browse the selection
on our Accessories
page.
Phone Hours
Mon-Fri
9AM - 5 PM
Central Time
Local: 325-227-6903
Toll Free: 866-807-4337
Email: sales@electricrider.com Service Dept: 325-227-6903 Go green with a company who will back
you up! Buy with confidence, we'll be here when you need us!
ElectricRider
1301 Pulliam Street
San Angelo, TX 76903
In our 11th year of service to the electric bike and LEV community
